Six basic issues needing attention in home decorat

2022-07-22
  • Detail

With the improvement of living standards, home decoration is no longer as simple as decorating a house. It has been endowed with richer connotation, and even has become an attitude towards life. Different types of decoration styles show the owner's different aesthetic tastes and cultural qualities. However, no matter how you decorate your home, some basic work still needs to be done. Although it has nothing to do with your quality and taste, the so-called style should be based on a certain foundation. Therefore, experts here tell you that in the process of home decoration, we should pay attention to basic problems such as wood quality, paint selection, waterproof construction and so on

with the improvement of living standards, home decoration is no longer as simple as decorating a house. It has been endowed with richer connotation, and has even become an attitude towards life. Different types of decoration styles show the owner's different aesthetic tastes and cultural qualities. However, no matter how you decorate your home, some basic work still needs to be done. Although it has nothing to do with your quality and taste, the so-called style should be based on a certain foundation. Therefore, experts here tell you that in the process of home decoration, we should pay attention to basic problems such as wood quality, paint selection, waterproof construction and so on

the quality of wood should be guaranteed

according to experts, the quality and price of wood vary greatly. It is best to choose materials with hard texture and not easy to decay. It's best to saw the large wooden board after buying it to release the stress to adapt to the microclimate of the room. Once the decorative panel comes in, it should be painted once to prevent cracking or soiling. The gypsum board shall be fixed with countersunk self tapping screws, which enter the board surface for 1~2 mm, and shall be treated with rust prevention. It cannot be hit with a nail gun. The distance between the gypsum board screws shall not be greater than 200 mm. It is best to stick kraft paper on the board joints and internal and external corners to prevent cracking

it is best to use dried Larch for the keel of the ground. The floor should be paved at 30 degrees or 45 degrees, 2-3 mm should be left between the plates, and the joints should be staggered. 8-10 mm should be left between the floor and the wall. When the length of the composite floor exceeds 8 meters, expansion joints should be considered (at this time, composite skirting lines cannot be used, otherwise the joints cannot be covered) Although termites and other pests occur less, it is best to place some insect prevention and insect repellent powder under the floor

in addition, experts also suggested that the upper and lower rails of the door should be painted, the bottom of the toilet door should be painted waterproof, and the sliding door made by yourself should not be made into a dark track, otherwise it will be troublesome to repair in the future. At the same time, try not to use MDF as door pocket

two rows of incomplete bricks are not allowed

before the bricklayer starts work, let the workers check whether there are hollows and cracks in the house. If there are, repair it first. Cement can't be used more than three months after the delivery date. At the same time, cement of different varieties and grades can't be mixed. Yellow sand must be used with medium sand. Wall and floor tiles must be soaked in water for more than two hours and can be pasted after drying in the shade. It's better to buy more pieces than less, otherwise once there is a color difference, it's not easy to remedy

it should be noted that there should be no two rows of incomplete bricks on one wall, and the tiles should be cleaned immediately after pointing. The ground is paved with light colored marble. Remember to use white cement for anti-corrosion treatment on the back of the stone. The external corner should be cut at a 45 degree angle. The floor tiles must be dirt resistant and non slip. At the same time, they should be inclined to the floor drain to avoid unnecessary ponding. The wall tiles should be cut in the form of casing when they touch the pipe opening, so as to ensure that they look like a whole brick. The marble on the ground is best in the form of dry paving. Matte tiles are difficult to clean, so be careful when choosing. Also, balcony floor tiles should use special floor tiles, otherwise it is easy to get dirty. At the same time, we should also pay attention to the drainage direction to avoid unnecessary trouble

tri water based paint has low environmental stimulation

wood paint try to choose paint products of well-known brands, and it is best not to blindly follow the recommendations of decoration companies or foremen. In the past two years, with the improvement of people's awareness of environmental protection, the amount of water-based paint used by brand companies is increasing rapidly. At present, the process of water-based paint has been greatly improved, but there are still weaknesses such as insufficient film plumpness, which you can choose at your discretion

as for the wall, you can brush glue once to seal it. It is better to use dacron cloth where there are cracks on the wall, and it is best to put bandages on the joints of gypsum board. Try not to mix water in the construction of darker and darker emulsion paint, otherwise it is easy to have color difference. The bright and mercerized emulsion paint should be completed at one time, and the color difference is easy to appear in the secondary paint repair. It should be noted that the second painting must be carried out after the previous one is completely dry, and the polishing can only be carried out after the paint surface is completely dry

when painting the door, the hinges and door locks should be pasted with masking paper. When pasting wallpaper, the wall should be painted with oil, and the panels of switches and sockets should be removed. After the skirting line is installed, the joints should be repaired with putty and emulsion paint. The paint construction on the metal surface must be treated with rust prevention. The frosted glass should be covered and protected in advance, and it is difficult to deal with it if it is stained with paint

four waterproofing should be subject to pressure test

membrane waterproofing should be used as much as possible in waterproof construction. The waterproof layer on the bathroom shower side should not be less than 1.8 meters. It is best to do more waterproofing in floor drains, internal and external corners, pipes and other places. Try not to walk the water pipe from the ground. The cold water pipe should have a protective layer of 1 cm in the wall, and the hot water pipe should have a protective layer of 1.5 cm in the wall, so the groove should be deep. Before sealing the groove, the pressure test must be carried out on the reconstructed pipeline with a water pressure several times higher than the daily water pressure to test whether there is water leakage at the joint. The waterproof works shall be carried out after the construction and acceptance of all concealed works, and the secondary water storage test must be carried out after the waterproof construction is completed

the hot and cold water pipes should ensure that the left is hot and the right is cold, which is more in line with people's usage habits. In addition, odor proof floor drains should be used for floor drains. When installing PPR pipes and galvanized pipes, the thickness of ceramic tiles should be considered to ensure that the pipes will not be exposed

five kitchen and bathroom decoration don't save money

practical functions must be considered in kitchen and bathroom decoration. Cooking takes only a few minutes, but washing takes a long time, so the water bucket in the pool must be large, and the faucet and basin should be matched. Some people have bought beautiful ones but can't fit them

福州不孕不育医院

昆明男科医院

重庆妇科医院

Copyright © 2011 JIN SHI